a-worker-kneels-and-places-a-large-ceramic-floor-tile-into-fresh-grooved-adhesive-with-a-stack-of-ti-product-1794012418

How to Fix Bathtub Chips Before Reglazing

To fix bathtub chips before reglazing, clean the damage, dry it fully, and lightly scuff the edges with 320-grit sandpaper.

Last Updated: November 6, 2026

Quick Summary

To fix bathtub chips before reglazing, clean the damage, dry it fully, and lightly scuff the edges with 320-grit sandpaper. Do not fill deep or metal-exposing chips yourself, because a refinisher may need to assess them first. Confirm the tub material and ask your refinisher before any repair.

  • Press the damage gently; if the finish lifts, the problem is bigger than the chip.
  • Clean with rubbing alcohol and dry the area completely before any work.
  • Sand acrylic or fiberglass lightly with 320-grit; stop early on steel or cast iron.
  • Leave chips that expose metal, rust, or loose edges for the refinisher to assess.
  • Refinish the whole tub when peeling is widespread, since patches tend to lift again.
Is your tub past a simple patch?Century BathTubs refinishes chipped and worn tubs in Toronto with a three-year guarantee.

Request Your Free Inquiry

Table of Contents

Assessing Bathtub Chips, Cracks and Peeling Before You Start

Before you fill anything, work out what you are dealing with. Our repair methods overview compares DIY kits with professional refinishing so you can decide which fits your damage. A chip is a small piece of the glaze that has broken away, usually down to the metal, steel or cast iron underneath, and repairing bathtub chips starts with knowing how deep the damage goes. A crack runs through the material itself, and a hole goes all the way through. Peeling is different again: the finish lifts in sheets or flakes, often around the drain or along the rim.

Overhead view of a person using a red-handled wrench to repair a chrome faucet on a white sink, with hex keys nearby.

Each one needs a different approach. Chips can often be repaired at home. Cracks and holes usually need a professional opinion, and widespread peeling generally means the whole tub should be refinished rather than patched.

Press the edge of the damage gently with a fingernail. If it catches or the finish lifts, the problem is bigger than the chip you can see. Check for soft spots, water staining or a dull, rough texture around the damage.

  • Small chip: a few millimetres, glaze gone, surface still sound around it
  • Crack or hole: the material is broken, or water gets through
  • Peeling: the finish lifts when you press or scrape it
  • Widespread wear: several chips, faded colour or a rough surface across the tub

Watch out: patching a crack or a hole with filler alone often fails within months, because water gets under the repair and the material keeps moving.

Gathering Your Bathtub Chip Repair Kit and Tools

You do not need much for a small chip. Most of the job depends on buying the right repair compound and preparing the surface well.

Typical items for a repair kit:

  • Two-part epoxy or porcelain repair compound, with its catalyst
  • 220-grit and 320-grit sandpaper
  • Rubbing alcohol and lint-free cloths
  • Masking tape to protect the surrounding tub
  • A fine-tip applicator or small brush
  • Disposable gloves and good ventilation

Match the colour of the repair product to your tub as closely as you can. Test a small amount on a hidden spot or on scrap material first, because most compounds look darker once they cure.

Cleaning and Dry-Preparing the Damaged Area

Clean the chip with rubbing alcohol on a cloth. Remove soap scum, oil and mineral deposits, since any residue stops the filler from bonding. Rinse with clean water, then dry the area completely. Wait until it is fully dry before you go on, because moisture is the most common reason repairs fail.

Mask the tub around the chip with tape so the filler only goes where you want it.

Sanding and Feathering the Edges for Bathtub Surface Preparation for Reglazing

Sanding a chip before reglazing is not the same as sanding before a DIY filler. When a professional refinisher will apply a new coating, your goal is to give that coating a sound, clean substrate without creating problems the refinisher has to undo.

Start by identifying the tub material, because it changes how much you should sand. Acrylic and fiberglass tubs have a gelcoat surface over a composite shell. Sanding through the gelcoat into the porous layer underneath creates a spot that absorbs moisture and can cause the new finish to blister. Steel and cast-iron tubs have a porcelain enamel layer over metal. Sanding through the enamel exposes bare metal, which rusts quickly and must be primed before any coating. If you are unsure what your tub is made of, check the underside or the manufacturer’s label, or ask your refinisher before you touch it.

For a small chip on any of these materials, lightly scuff the edges with 320-grit sandpaper. The goal is to remove loose, flaking glaze and feather the hard edge so there is no sharp step between the damaged area and the sound finish. Work gently and stop as soon as the edge feels smooth to the touch. Do not try to sand the chip flat or remove all the discoloration; that is the refinisher’s job.

Finish with a few light passes of 220-grit paper, then wipe the dust away with rubbing alcohol on a lint-free cloth. Do not use household cleaners, oils, or tack cloths that leave residue, because those can interfere with the bonding agents in professional refinishing systems.

Watch out: sanding too aggressively can widen the chip, scratch the surrounding glaze, or expose material that the refinisher then has to repair before coating. If you are not sure how far to go, stop early and let the refinisher assess it.

If you plan to have the tub professionally reglazed, this step matters most. A chip sanded smooth and clean gives the refinisher a sound base. A chip filled with a rough or uneven patch can telegraph through the new finish. Check with your refinisher before you fill anything, because some prefer to see a chip left unrepaired so they can assess the damage and prepare the surface with their own methods.

The right sanding depends on what the tub is made of, so check the material before you touch the chip.

Tub materialSanding riskWhat to do
Acrylic or fiberglassSanding through gelcoat exposes porous layerLightly scuff with 320-grit only
Steel or cast ironSanding through enamel exposes bare metalStop early; metal must be primed
Unsure of materialWrong approach can cause damageCheck underside or ask refinisher
Any tubOver-sanding widens the chipFeather edges, then finish with 220-grit

Mixing and Applying the Filler to Chips Only

Before you mix anything, decide whether filling the chip is the right move at all. If a professional refinisher will coat the tub afterward, some chips should be left alone. A chip that is clean, dry, and free of rust or exposed metal can often be left open for the refinisher to assess and prepare with their own fillers and primers. Filling it yourself with a hardware-store epoxy can create a bond that the refinisher’s coating will not adhere to, or a surface that telegraphs through the new finish.

A smiling woman in a striped top talks on her phone beside a laughing man at a desk with a laptop.

Leave the chip unrepaired and document it if any of these apply:

  • The chip exposes bare metal or shows rust
  • The chip is larger than a few millimetres or has loose edges
  • The surrounding finish is peeling, cracking, or soft
  • You are not sure what the tub is made of
  • The refinisher has asked to see the damage before any repair

If you and your refinisher agree that a DIY fill is appropriate, match the filler to the tub material. For acrylic and fiberglass tubs, a two-part epoxy or acrylic repair compound designed for plastics works best. For steel and cast-iron tubs with porcelain enamel, use a porcelain repair compound or a two-part epoxy rated for metal. Do not use silicone caulk, spackle, or auto body filler; these do not bond well to tub surfaces and can fail or interfere with reglazing.

Mix the two-part compound exactly as the label says. Too much catalyst makes it cure too fast and can cause shrinkage or cracking. Too little leaves it soft and tacky. Mix only as much as you can apply in a few minutes, because most compounds start to set quickly.

Apply the filler with a fine-tip applicator, pressing it into the chip and keeping it inside the damaged area. Build it up in thin layers if the chip is deep. Let each layer cure fully before you add another. Keep the filler off the healthy finish. Remove any excess right away while it is still soft, and leave the surrounding tub alone.

Once it has cured, sand the repair flush with the tub using 320-grit paper, then finish with a light pass of 220-grit. Wipe clean with alcohol and check the result under good light. If the repair feels rough or the edge catches your fingernail, sand it again lightly. A smooth, feathered repair is less likely to show through a new coating.

Watch out: a filler that is too hard, too soft, or chemically incompatible with the refinisher’s coating can cause adhesion failure or visible ridges under the new finish. When in doubt, leave the chip unfilled and let the refinisher handle it.

Dealing With Peeling Finish and Bathtub Peeling Finish Repair

Peeling finish is harder to fix at home. Scraping off the loose material exposes the metal, and a patch placed over a failing finish will usually lift again.

Remove all loose flakes with a scraper and sand the edges of the sound finish. Clean the area well, then assess how much of the tub has gone. If peeling covers more than a small area, the finish has reached the end of its life.

Watch out: a patch over peeling finish can trap moisture underneath and make the problem spread.

Refinishing the whole tub is usually the better fix when peeling is widespread. It removes the failing surface and gives the entire tub a new, consistent finish.

Booking Professional Bathtub Refinishing Toronto Homeowners Can Rely On

If the damage is deep, widespread or has reached the surface, a professional refinish is often the most reliable choice. At Century BathTubs, we restore worn, chipped and faded bathtubs and shower tiles with our EP-ACRYLIC coating system. Our trained, licensed and insured technicians prepare the surface properly before applying the new finish.

Every job comes with a three-year hassle-free guarantee. Pricing depends on the size of the tub, its condition and the finish you choose, so contact us for a quote for your specific project. See the Toronto reglazing cost guide for the main cost drivers.

Ready to stop patching and start over? Request your free inquiry with Century BathTubs and get a clear plan for your Toronto bathroom.

Frequently Asked Questions

Should you repair bathtub chips before reglazing?

Yes. A reglazing coat is thin and will show every chip, crack or hole underneath it, and it cannot bridge a gap. Filling chips first gives the refinisher a smooth, sound surface to coat. Shallow chips are straightforward to fill yourself with a two-part porcelain repair compound. Deep cracks, holes that go through to the substrate, or extensive peeling are better assessed by a professional, who can decide whether the tub can be refinished or needs other work. Contact Century BathTubs for an assessment before any work begins.

How do you fix a chip in a bathtub before refinishing?

Clean the chip with rubbing alcohol, dry it fully, and lightly sand the edges with 220-grit sandpaper so the filler has tooth. Mix the two-part epoxy or porcelain repair compound according to the label, then apply it in thin layers with a fine applicator, slightly overfilling the chip. Once cured, sand the filler flush with 320-grit paper so it sits level with the surrounding finish. Wipe away dust and confirm the surface is smooth before any reglazing coat is applied.

Can you reglaze a bathtub with chips or peeling finish?

Small, stable chips can usually be filled and then reglazed. Peeling finish is different: the coating is no longer bonded to the tub, so a new coat applied over it will lift with it. Loose or flaking areas need to be removed and the surface properly prepared before refinishing. A refinisher can assess whether the tub is sound enough to coat. Ask for an inspection before booking, since a chipped or peeling tub that is not prepared correctly can fail within a short time.

How long should a bathtub chip repair cure before reglazing?

Curing time depends on the product, so follow the drying and cure times printed on the repair compound label. Two-part epoxy repairs generally need several hours to become workable and longer to cure fully before sanding or coating. Avoid using the bathroom and running water over the repair during this period. Rushing the cure can cause the filler to soften or lose adhesion under the new finish. If you are scheduling with a refinisher, confirm that the repair has cured fully before the appointment.

Share this post